2024 Carrier/Bryant Zoning Live
Quiz Summary
0 of 32 Questions completed
Questions:
Information
You have already completed the quiz before. Hence you can not start it again.
Quiz is loading…
You must sign in or sign up to start the quiz.
You must first complete the following:
Results
Results
0 of 32 Questions answered correctly
Your time:
Time has elapsed
You have reached 0 of 0 point(s), (0)
Earned Point(s): 0 of 0, (0)
0 Essay(s) Pending (Possible Point(s): 0)
Categories
- Not categorized 0%
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
- 25
- 26
- 27
- 28
- 29
- 30
- 31
- 32
- Current
- Review
- Answered
- Correct
- Incorrect
-
Question 1 of 32
1. Question
The primary objective of a zoning system is what?
CorrectIncorrect -
Question 2 of 32
2. Question
When selecting equipment for zoning it is always best to use ____________.
CorrectIncorrect -
Question 3 of 32
3. Question
On a “DIRECT RETURN” type bypass how far from the equipment should the bypass duct be connected?
CorrectIncorrect -
Question 4 of 32
4. Question
Can you only use Carrier/Bryant Dampers with Comfort & Legacy 3-Zone zoning systems?
CorrectIncorrect -
Question 5 of 32
5. Question
Does the ZONEXX3ZAC/HP01 zone board require a separate transformer?
CorrectIncorrect -
Question 6 of 32
6. Question
If the HPT sensor is not used with a ZONEXX3ZHP01 you must do what?
CorrectIncorrect -
Question 7 of 32
7. Question
How many dip switches are there on the ZONEXX3ZHP01 HP zone control board?
CorrectIncorrect -
Question 8 of 32
8. Question
How many dip switches are there on the ZONEXX3ZAC01 AC zone control board?
CorrectIncorrect -
Question 9 of 32
9. Question
On a ZONECC4ZCN01, how many dampers can be used per zone and do they require a separate transformer?
CorrectIncorrect -
Question 10 of 32
10. Question
Is there an Installer Test Mode in ZONEXX3ZAC/HP01 Zoning Systems?
CorrectIncorrect -
Question 11 of 32
11. Question
The AC Zone Control Board ZONEXX3ZAC01 supports only? CorrectIncorrect -
Question 12 of 32
12. Question
When using a duct calculator, it is based on what assumed measurement?
CorrectIncorrect -
Question 13 of 32
13. Question
What is the maximum number of zones that are available when using Infinity™ & Evolution™ Zoning? CorrectIncorrect -
Question 14 of 32
14. Question
Can you mix Rectangular, Slip-in, and Round Dampers? CorrectIncorrect -
Question 15 of 32
15. Question
In what document can you find a piece of equipment’s airflow ratings? CorrectIncorrect -
Question 16 of 32
16. Question
Is cooling airflow always higher than heating airflow? CorrectIncorrect -
Question 17 of 32
17. Question
How many polling questions were there in todays class?
CorrectIncorrect -
Question 18 of 32
18. Question
If you could use multiple dampers how do they wire into the system? CorrectIncorrect -
Question 19 of 32
19. Question
How do you change the Smart Sensors zone address? CorrectIncorrect -
Question 20 of 32
20. Question
How do you lock the new Smart Sensor? CorrectIncorrect -
Question 21 of 32
21. Question
With the “preferred method” how many wires should you connect to each terminal on a ABCD Green Plug Connector? CorrectIncorrect -
Question 22 of 32
22. Question
Where do you find the systems minimum airflow? CorrectIncorrect -
Question 23 of 32
23. Question
Can you install a duct with no damper or control to be just a dump zone with Infinity/Evolution Zoning? CorrectIncorrect -
Question 24 of 32
24. Question
How can you determine if a zone is addressed correctly? CorrectIncorrect -
Question 25 of 32
25. Question
How many Airflow Limit settings are there for an Infinity/Evolution Zoning system? CorrectIncorrect -
Question 26 of 32
26. Question
With Infinity/Evolution zoning, if a stage can’t handle the systems minimum airflow it will do what first to protect itself. CorrectIncorrect -
Question 27 of 32
27. Question
When an Infinity® & Evolution® Zoning system goes into cutback mode it reduces the blower speed by what? CorrectIncorrect -
Question 28 of 32
28. Question
When troubleshooting a Comfort™ & Legacy™ Series Three-Zone System, what does a continuous on LED indicate?
CorrectIncorrect -
Question 29 of 32
29. Question
How many ABCD terminals are there on an Infinity® & Evolution® Zoning board? CorrectIncorrect -
Question 30 of 32
30. Question
If you have a Airflow Limit-Stage down occurrences with no under-conditioning is this a problem?
CorrectIncorrect -
Question 31 of 32
31. Question
When using a Infinity® & Evolution® Zoning System, what position should the furnace SW4 dip switches be set to? CorrectIncorrect -
Question 32 of 32
32. Question
What must you do to make an Infinity® or Evolution® Zoning Damper Module be recognized as zones 5 – 8? CorrectIncorrect
English 
Spanish